Please excuse our construction of this page. We are redesigning this page to better display the products that we offer. Click on any of the product
photos to gain more information on that product. The links on the left side of the screen will take you to that catagory.

LS-1-2 6-7-9 Fuel Lines
Quick, simple installation and all stainless construction. Choice of thru the cover or hidden under the cover for any LS type engine. 		$103.95 single line $165.95 two line

93 CAMARO Fuel Lines
Simply unplug your stock lines and plug these in. Passenger and driver side kits have 30" hoses with 06 AN bottom fittings. Supply line has fuel pressure port. Custom lengths and hose ends by request.
 $165.00 Dual Line
94-97 CAMARO LT-1 Fuel Lines
Passenger and driver side kits route your fuel lines behind your engine and allow the use of corvette injector covers. All stainless construction. Kits come with ss clamp, 24" hoses and 06 AN female ends unless otherwise specified. See custom hose section.
$165.00
LS-1-2 6-7 with Magnuson Blower Fuel Lines
Single or dual line kits install quickly and easily. All stainless construction with 36" hoses and 06 AN female ends unless otherwise specified, clamp included.

 $165.95
92-96 CORVETTE fuel line kits
Send us your fuel rails from these years corvette engines and we will convert them to passenger or driver side lines. Kits come with 30" hoses and 06 AN end fittings.
 $165.00
Dual Line
CHRYSLER HEMI
All stainless construction, quick easy installation. Standard kit has 36” hose and 06 AN female end. Custom lengths and end fittings available. See hose end selection sheet.

 $103.95
Big Block RamJet
Fuel & Brake Vac Lines
Kits for passenger or driver side come with 14 & 16 mm O-Ring adaptors. Passenger side kits have 30" hoses, driver side have 26" hoses. Both have 06 AN female ends unless otherwise specified. See custom hose end section.		 $165.00
Big Block RamJet
Chrome PCV & PCV Line
PCV line kit (Stainless Hard Line ONLY)		 $34.95
Big Block RamJet
Brake Vacuum Line (Stainless Hard Line ONLY)		 $24.94
Braided Stainless Steel Carburetor Dual Inlet Line Kit
1/8" NPT gauge port
Pre-assembled and ready to install - Power-flo radius carburetor fittings for smooth fuel flow
Braided Stainless steel hose between fittings adds safety and performance
- Anodized fittings - 1/8" NPT port for optional gauge provision - Includes Steel crush inlet washers
call
Chrome Fuel Line 3/8 in. Hose Barb Inlet,
1/8 in. Gauge Port
(10010) Fits 4150 Series Holley Double Pump Carburetors with Dual Feed Inlet 9-5/16" Centers
(10011) Fits 4160 Series Holley Vacuum Secondary Carburetors with Dual Feed Inlets
8-21/32" Centers 		call
Tube Tech Nylon Fuel Line Kit
Everything you need to plumb any Fuel injected vehicle with any GM or Chrysler Engine.
$249.00
$269.00
-6, -8, -10, -12AN Stainless Steel Hose - 20 ft roll packaged
Made of durable CPE synthetic inner rubber tube- Bonded with woven nylon braid for added strength
308 Stainless steel outer braid - Resists heat, abrasion, and corrosion
Operating temps from -40 to +350 degrees F
Compatible with alcohol, synthetic, and petroleum based fuels, motor oils, and antifreeze.

 call
-6, -8, -10, -12AN Black Nylon Lightweight Race Hose - 20 ft roll packaged
Made of durable CPE synthetic inner rubber tube
Bonded with black woven nylon braid for added strength and weight saving performance
Maximum pressure rated at 350 PSI - Operating temps from -40 to +302 degrees F
Compatible with alcohol, synthetic, and petroleum based fuels, motor oils, and antifreeze

call
3/8" - 1/2 ' - 5/8" Diameter Aluminum Fuel Tubing 25' Coil
.035'' wall, seamless aircraft tubing - Easily bends into the exact shape you need
Designed for use in carbureted applications - For use with fuel pressures less than 25 PSI.
- Made in U.S.A.

call
Aluminum clamps insulated with Adel rubber material.
Makes mounting fuel lines and wiring easy.
1/4" pkg 20 - 3/8" pkg 20 - 1/2" pkg 15 - 5/8" pkg 12 - 3/4" pkg 10 - 1" pkg 6

call
55-57 Chevys
Polished stainless lines mount on the outside of the passenger side Frame Rail and go thru the body support brackets.
Complete Kit
$495.00 to $595.00
Frame lines
$159.00 to $269.00
58 - 64 Impala
Single & Dual line kits run on the passenger side of the frame & come polished with stainless 06 AN ends. Stainless clamps & mounting screws included.
Complete Kit
$449.00 to $549.00
Frame lines
$139.00 to $259.00
64-72 CHEVELLE SINGLE OR DUAL LINE KITS

Complete Tank to Engine Kit for any single or Dual line fuel injected engine, comes with fuel filter regulator, engine to frame kit, hard lines, rear hoses, clamps, mounting screws and tank fittings.

Complete Kit
$449.00 to $549.00
Frame lines
$139.00 to $259.00
65 - 68 Impala
Your choice of Engine to Frame lines attach to S.S tubing which runs down the outside of thepassenger frame rail. At the rear S.S braided Hose is used to go over the rear end to the filter & Tank connections. All stainless mounting hardware included.
Complete Kit
$449.00 to $549.00
Frame lines
$129.00 to $239.00
67-69 Camaro
Single and dual lines run in the same position as the original fuel lines. The polished stainless hard lines run on the outside of the passenger side frame rail on the front and on the inside of the frame rail at the rear.
Complete Kit
$495.00 to $595.00
Frame lines
$159.00 to $279.00
64 -72 El Camino
Single & Dual line kits come polished with stainless 06 AN ends. Our Lines run in the same postion as the original lines. Stainless clamps & mounting screws included.
Complete Kit
$429.00 to $529.00
Frame lines
$89.00 to $179.00
Transmission Lines

Each set is Custom Made to your specifications and are available for any GM powered vehicle with any Engine - Transmission - Radiator combination.

$195.95
Filter Regulator Kit

GM '99 & Up LS-1,2,3,6,7, & 04 & Up 5.3 & 6.0.

Chrysler Small Block & Big Block HEMI'S

 Complete Kit $174.95
Billet In-Line Street Fuel Filter
-6 and -8 AN Male - Blue, black or polished finish
Made from lightweight billet 6061-T6 aircraft aluminum - - 40-Mircon stainless steel filter (washable)
Flows 95 GPH @ 7 PSI - Precision CNC machined - - 2-piece design, O-ring sealed, threaded end
 call
-8, -10 AN Billet In-Line Race Fuel Filter with a 10 Micron cellulose pleated filter and blue anodized finish
Precision CNC Machined from lightweight billet 6061-T6 aircraft grade aluminum
2-piece construction with o-ring seal - 10 Micron cellulose pleated fuel filter
Flow is rated at 150 GPH @ 9 PSI - For EFI and carburetor applications
- Blue anodized finish - For use with gasoline only - Laser etched Big End logo and flow arrow
call
High Flow Chrome Canister Filter - Classic Street/Strip Remote Style Fuel Filter
Classic remote style chrome canister fuel filter. - Flows up to 90 GPH @ 9 PSI
3/8" NPT female inlet/outlet ports - Painted cast aluminum housing - Chrome plated filter canister - 10 micron paper element - Chrome plated mounting bracket
For use on all carburetor style fuel systems
call
Glass Fuel Filter 5/16" or 3/8" hose
Chrome housing ends with a clear glass center. Universal Fit (not for fuel injection). Visually inspect the condition of fuel and element. Uses a standard replacement filter element BEP11055
 call
Street Chrome Fuel Filter
3/8" Hose Barbed Inlet/Outlet
Two piece design for easy filter replacement - Chrome plated housing
Uses sintered bronze carburetor element - For carburetor fuel system only
 call
SBC - BBC - SBF Mechanical Street or Race Fuel pump.
STREET PUMPS have 80GPH (free-flow). Shut-off pressure pre-set at 7 ½ psi. Heavy-duty construction for high RPM operation. Regulator not required on Holley or Demon carbs. RACE PUMPS have110GPH (free-flow) High output fuel flow. Shut-off pressure pre-set at 6 ½ to 8 psi. Heavy-duty construction for high RPM operation. Regulator not required but recommended on some applications. Manufactured by Holley.
call
Electric Fuel Pumps
Street Electric Fuel Pump 95 GPH pre-set factory 7 PSI
Street/Strip Electric Fuel Pump with Pressure Regulator Flows 110 GPH free flow and capable of 14 PSI to the pressure regulator.
Race Electric Fuel Pump Flows 140 GPH free flow and max pressure of 14 PSI at the regulator Compatible with alcohol and methanol fuels		 call
Adjustable Fuel Pressure Regulator
4.5 to 9 PSI - Shiny Finish
3/8" NPT ports - .220" (7/32") restriction
High Pressure (4-1/2-9 PSI)Includes mounting bracket
For carburetor use only
call
Chrome Plated Steel Small Block Chevy and 90 Degree V6 Fuel Pump Mounting Plate
Chrome plated steel - Replaces stock for engine dress up
Mounting gasket included
call
Billet Aluminum Fuel Block-Off plate SBC, BBC, Ford, Mopar
Aluminum, Blue or Red Anodized
Fits Small Block Chevy 265-400 - 4-Hole bolt pattern
Precision CNC Machined from 6061-T6 Billet Aluminum
Made in the U.S.A.
 call
Chrome Plated Steel Block Off Plate
(10050) Fits SB Chevy 265-400 (10055) Fits Big Block Chevy 396-454, Mopar V8, Pontiac V8, Oldsmobile V8, Ford V8 (except 351C, 400M, FE)
For use to cover up the hole after removal of the mechanical pump when switching to an electric fuel pump. Perfect engine dress up your engine with a chrome plated steel block-off plate. Mounting gasket included.
 call
Stainless Compression Fittings
Tube to Tube Unions
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
3/16 to 1/2		 $28.00
to
$38.50
Tube to Tube 90 Degree Unions
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
3/16 to 1/2		 $28.00
to
$45.00
Tube to Tube Reducing Unions
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $28.50
to
$32.50
Tube to Pipe Straits
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $18.50
to
$31.50
Tube to Pipe 90 Degree
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $18.25
to
$35.00
Aluminum Hose Ends
Constructed from lightweight 6061 alloy aluminum and designed for smooth flow, easy assembly and longer life.All elbows are built from one piece bullet tube construction. 37 degree AN flare assures a leak proof seal. Sizes -6 to -12 AN. Style Straight Swivel - 45 Degree Swivel - 90 Degree Swivel.		 call
Custom Socket Fittings

Customized performance plumbing options made easy with assorted color choice of Big Ends custom socket fittings. Replaces the standard red or black anodized socket section of Big End hose ends. Colors - Blue - Red - Purple - Green - Gold - Clear		 call
Straight Adapter Fittings
37 degree AN flare fits all standard AN hose ends, sold each.

1/4"NPT to -6AN 3/8"NPT to -6,-8,-10 AN
1/2"NPT to -6,-8,-10,-12AN 3/4"NPT to -12AN		 call
Port Plugs w/ O-Ring
Used to plug open ports or lines.
Blue anodized, sold each.
-6AN to -12AN		 call
Allen Socket Pipe Plugs
Blue Anodized.
1/8"NPT 2/pkg. 1/4"NPT 2/pkg. 3/8"NPT 2/pkg. 1/2" 1/pkg. 3/4"NPT 1/pkg		 call
AN Flare Cap
Blue Anodized. Sold ea.
-6AN to -12AN 		call
Tube Nuts
Blue Anodized.
-6 Tube Nut, 2/pkg
-8 Tube Nut, 2/pkg
-10 Tube Nut, each		 call
Tube Sleeves
Blue Anodized.
-6 Tube Sleeve Pr.
-8 Tube Sleeve Pr.
-10 Tube Sleeve Ea.		 call
AN Radius Port Adapteers with O-Ring
-6 port to -6AN or -8AN
-8 port to -6AN ,-8AN or -10AN
-10 port to -6AN, -8AN, -10AN or -12AN
-12 port to -10AN or -12AN		 call
Gauge Adapters
1/8" NPT gauge port adapter fittings. AN to AN or NPT to AN.
-4F to -4M, 1/8" NPT port * -6F to -6M, 1/8" NPT port * 3/8" NPT M to -6M 1/8" port
-8F to -8M, 1/8" NPT port * 3/8" NPT M to -8M 1/8" port
(F= Female Threads, M= Male Threads)		 call
Carburetor Inlet Adapter

-6AN to Edelbrock and Carter AFB or 7/8 Holley Dual Inlet or 9/16 BG Demon
-8 AN to 7/8 Holley short or long style
-8 AN to BG Demon 		call
Big End adjustable AN wrenches

They prevent scratching of aluminum anodized hose ends and fittings during installation and removal. Lightweight and easy to handle with a comfortable grip.

Made of billet aluminum, anodized blue

call
Chrome EGR Block Off Plate
This block-off plate allows you to seal the EGR passages in your intake manifold for off-road, and non-emission legal race use.
Chrome plated steel - Comes complete with gasket, bolts and washers
 call
Compression to 06AN Adaptors

These work great on all LT-1, LT4, LS1-2-3-6-7 & 9 & up GM Fuel Filter/Regulators.
Tube to AN 37 Degree Flare Union
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $22.33
to
$33.33
Tube Nuts
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $8.50
to
$11.50
Ferrule Sets
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $4.50
to
$6.50
Male & Female End Caps
These fittings work on Steel, Stainless Steel and Nylon tubing. They eliminate the need for flairing. Just slide the tubing into fitting until it bottoms out and then tighten the tube nut 1 1/4 turns. When installed properly they hold pressure until the tubing explodes.
 $11.50
Gauges / Instruments
Tachometer with Shift Light
Adjustable shift point indicator sets shift light. Chrome bezel w/black housing with backlit dial. Used with conventional or electronic ignition system (except MSD or C.D. ign. systems). For use in 4,6 or 8 cylinder engines		 call
Tachometer
0-8000 RPM Tachometer,white face with black numbers
Features: Adjustable dial on face to set shift point indicator. Chrome bezel w/black housing with backlit dial. Used with conventional or electronic ignition system (except MSD or C.D. ign. systems). For use in 4,6 or 8 cylinder engines
 call
2 5/8" Large Diameter Gauges
Race styling for serious high performance. Features Full-Sweep dial with black face, white pointer and race-style chrome bezel. All gauges come complete with adapters, tubing, light kit, mounting hardware and instructions
Voltmeter, Fuel Pressure, Oil Pressure, Oil Temp, Vacuum, Water Temp.		 call
Trio Gauge Panel w/ Water Temp /Oil Pressure/ Ammeter
Dual Gauge Panel w/ Water Temp/ Oil Pressure
Large diameter for that serious high performance look. All gauges come complete with adapter, tubing, light kit, mounting hardware and instructions. Available in Dual & Trio Kits

 call
Chrome Trio Gauges Water/oil/amp
Black Trio Gauges Water /oil /amp
Black Trio Gauges water/ oil/ volt

Features: 2” Diameter mechanical gauges installed on a 3 gauge mounting panel. Black face with a white dial and red pointer. All gauge sets include adapters, mounting hardware, light kit and instructions

 call
2-5/8" Gauge Panels & Mounting Cap (Single Gauge Mounting Cup)
2-5/8" Gauge Panels & Mounting Cup (single gauge panel)
Features: Chrome-plated cup and panels. Fits 2-5/8” individual gauges. Panels available in single, dual and triple
 call
Chrome 0-15, 0-30, 0-60 or 0-100 PSI Pressure Gauge
Black face with white numbers and pointer - Chrome bezel and cup
Small 1-1/2” diameter - Brass internals for long life - 1/8” Male N.P.T center back mount

call
Liquid Filled 0-15, 0-30, 0-60, 0-100 PSI Pressure Gauge
Black face with white numbers and pointer - Chrome bezel and cup
Small 1-1/2” diameter - Shock Proof, Glycerin filled to protect internals against vibration damage and longer gauge life - Brass internals for long life. 1/8” Male N.P.T center back mount
call
Engine Turned 0-15, 0-30, 0-60, 0-100 PSI Pressure Gauge
Machined finish dial with black numbers and pointer - Chrome bezel and cup
Small 1-1/2” diameter - Shock Proof, Glycerin filled to protect internals against vibration damage and longer gauge life - Brass internals for long life
- 1/8” Male N.P.T center back mount
 call
Tire Pressure Gauges 0-30PSI
Large 2-5/8” diameter dial, easy to read. Protective rubber bezel for shock resistance. Finger-operated air bleed valve allows for quick pressure adjustment. Heavy-Duty 13mm hose with air chuck valve for easy access to all valve stems 		call
Liquid filled 0-15, 0-30, 0-60, 0-100 PSI Comp Series pressure guage

White face with red pointer, 1-1/2" Dial, Rugged Stainless Steel Case
Brass Internals, Dry or Liquid Filled for Vibration Dampening, Acrylic Lens
1/8" NPT Center Back Connection

Liquid Filled Nitrous Oxide Pressure Gauge
0-1500 PSI, Black Face with Yellow dial and Cross Checkered Flags, Red Pointer or white face with red pointer
Monitors bottle pressure, either on bottle or in the front of the solenoid.
Chrome bezel and cup - Small 1-1/2” diameter - Shock Proof, Glycerin filled to protect internals against vibration damage and longer gauge life
- Brass internals for long life - 1/8” Male N.P.T center back mount
2-1/16" Color Control Trio Panel
Mechanical Water Temp, Oil Pressure, Voltmeter with push button color control
Push button changes color from white, green, blue, red, yellow, pink, and light blue on each individual gauge - Bright red back lit pointer - Chrome panel with brushed aluminum bezel
Includes all installation hardware, adapters, and 12 volt lighting kits
Liquid Filled Engine Thermometer 0-250 F
Features: Chrome 2” diameter gauge, 0°-250° F. Mount it on an intake manifold or head for water temperature reading. Glycerin filled for vibration protection. Screws Directly into a 3/8” NPT fitting
Oil Pressure Installation Kit
Replacement nylon line kit for all oil pressure gauges
Includes 72" 1/8" nylon line and fittings
Heat Protection Products
Exhaust Insulating Wrap (Graphite Black)
The original Exhaust Insulating Wrap was developed over 12 years ago by Thermo-Tec. Exhaust Insulating Wrap is an innovative way to create more horsepower and reduce under-hood temperatures.
 $25.00
to
$125.00
Exhaust Insulating Wrap
The original Exhaust Insulating Wrap was developed over 12 years ago by Thermo-Tec. Exhaust Insulating Wrap is an innovative way to create more horsepower and reduce under-hood temperatures.
$35.00
to
$150.00
Snap Strap
Easily secures the exhaust insulating wrap with no tools needed. Made of high temperature stainless steel. New precut lengths with a tough multi-lock system.		 call